blinkgogl.blogg.se

1. #XECUTER JR PROGRAMMER V2 DRIVERS INSTALLER UPDATE#
2. #XECUTER JR PROGRAMMER V2 DRIVERS INSTALLER REGISTRATION#

LokSound 5 family: Sound compiler sometimes left a state without sound sample too early occasionally.LokSound 5 DCC Decoders now get back the 3-point speed control using CV 2, CV 6 and CV 6. new firmware 5.0.67 for LokSound 5 Family: Soundslot 1 and Soundslot 2 determine if the driving sound is on for Random sounds.Bugbix: When replacing sound files sometimes the volume settings were lost.Sound simulator: Did hang sometimes on low performance computers.Sound simulator: Sometimes did not reproduce 'immediate/cross' transitions.CV 23 and CV 24 adjustment did not work correctly. Bugfix: Constant brake distance did not work on speedstep 0. New Firmware 5.0.71 for LokSound 5 decoders: New light effect 'Servo Power Control'.Drivestop available in Soundslot 1 and Soundslot 2 now

#XECUTER JR PROGRAMMER V2 DRIVERS INSTALLER REGISTRATION#

Registration on Mobile Station 1 works again. New firmware 5.0.73 for LokSound 5 decoders: Now automatic detection with M채rklin Central Station 3 and 32 functions works again.New menu Tools - LokProgrammer Device shows the hardware revision of the LokProgrammer used.Improved stability when writing LokSound 5 sound data.Fixed bug when controlling Gauge 1 smoke units (KM-1, Kiss) New Firmware 5.0.78 for LoKSound 5 Decoders: Optimized motor control (more silent).Now you can also select SUSI Slave to control LokSound Decoders externally. Firmware 5.1.85 for LokSound 5 family: Now you can enable F0, F1 - F30 for control in consist mode.New Register 'Current Speed' can be used in sound charts. Soundeditor: Double comment after opening a Multichannel Steam engine removed.Read Decoderdata: Values for Servooutput Position B was not shown correctly sometimes.BEMF: CV116 can have lower values down to 25 now for better control during slow speed. RailComPlus and M4 Master Decoder Synchronisation. Optimization for ZIMO HLU operation using Stein and MX9: More reliable detection. New light function Brake light: Light will automatically turn on while braking. Modified SUSI Support for Brawa locomotives. Firmware 5.1.101 for LokSound 5 Family: Soundslot Settings: Volume for each soundslot now up to 255 (instead of 128) for more volume.Soundeditor: Default Size for Mute and Containers are changed.Read and write Decoder data: Optimisation for faster decoder detection.Soundsimulator - Actions => Reset Bits of Registers.New CV 245 adds waiting time for automatic coupler sequence

Firmware 5.3.115 for LokSound 5 and LokPilot 5 family: Fixed bug with grde crossing and flash lights.Bugfix: Fixed SUSI-Problem with Brawa locomotives. Bugfix: Using Motorola Programming mode, now the correct outputs are flashing. Bugfix: Output mode 'Fliashing light' did not work properly with Grade crossing. Load dependend sound: The sound schedule's acceleratin is now immediately following 'Optinal / Primary Load'. Added CV 122 Bit 3 to double the amount of steam chuffs when shunting mode is active. Ditch Light type1 now has fade-in and fade-out. Firmware 5.3.122 for LokSound 5 and LokPilot 5 Familie: New light output mode: Digitl coupler Coil#2.Significantly improved Analog AC and DC motor control: Much better and smoother running on older motors. New Firmware 5.3.125 for LokSound 5 and LokPilot 5 Familie: F16-F31 will now also follow RCN212, Section 2.3.7. New warning messages if output configuration is wrong.

#XECUTER JR PROGRAMMER V2 DRIVERS INSTALLER UPDATE#